Sapphire Black + Bright Gold + Reflective Diamond + Crystal Clear

 

Products used:

- Glowdip starter set

- Colour: Sapphire Black

- Colour: Bright Gold

- Colour: Reflective Diamond

- Colour: Crystal Clear

Step-by-step instructions for applying " Sapphire Black + Bright Gold + Reflective Diamond + Crystal Clear" Dipping Powder

Materials:

• Sapphire Black Dipping Powder
• Bright Gold Dipping Powder
  
• Reflective Diamond Dipping Powder
• Crystal Clear Dipping Powder
• Base coat
• Activator
• Top coat
• Nail file and buffer
• Dusting brush or soft brush

Preparation

File your nails into the desired shape and gently push back your cuticles.

For optimal adhesion, lightly roughen/match the natural nails with a buffer block or the fine side of a file before application.

Be sure to remove invisible cuticle and skin debris as well, to avoid lifting.

Do not apply oils or creams before use.

Step 1: Base coat

Apply a thin, even layer of base coat to all nails except the thumb, middle, and ring finger, then dip these nails fully into “Sapphire Black.” Hold the finger at a slight angle for smooth coverage, tap off excess powder, and softly brush away loose particles. Allow this layer to set before moving forward so the base color looks clean and even.

For the thumb, middle, and ring finger, apply a thin layer of base coat, but do not dip yet. Using a slim nail art brush, carefully draw upward strokes starting from the lower half of the nail and moving upward at varying heights. The strokes should be irregular and scattered, mimicking the look of fireworks bursting upward. Work slowly and lightly so the lines stay crisp and intentional.

While the base coat on the strokes is still tacky, begin layering the powders in sequence. First, lightly dip or sprinkle “Sapphire Black” over the design to define the base of the fireworks. Next, repeat the process with “Bright Gold” to add warmth and contrast, followed by “Reflective Diamond” to bring in sparkle and dimension. Gently tap off excess powder after each color and brush away loose particles carefully so the design remains sharp and layered.

Once the firework design is complete, apply a final, even layer of base coat over the entire nail and dip into “Crystal Clear.” This encapsulates all the layers, smooths the surface, and protects the design underneath.

Be sure to cover the edges well, but do not touch the skin around the nail.

Step 2: Base Coat & Color Powder

Repeat step 1 for optimal coverage, adhesion and beautiful and stunning color intensity.

Step 3: Activator Coat

Apply enough Activator Coat over the entire nail surface, edges and also at the tip. The Activator is the most important step in the application process because it seals and binds the layers to the nail, preventing air bubbles from forming and ensuring long-lasting adhesion. Allow the Activator Coat to dry for at least two minutes.

Step 4: Filing & Polishing

Now you can use the fine side of the file or a buffer to buff away all bumps and imperfections and bring the nails to the desired shape and thickness. It is important to file carefully so that you do not damage the surface and nails.

Step 5: Activator Coat

Repeat step 3. Again, apply enough Activator Coat to the entire nail and its perimeter to seal the layers optimally. Then allow the Activator Coat to dry for at least two minutes. To make sure the Activator Coat is dry, you can clean the surface of the nail with a paper towel after 2 minutes. This is to prevent the Top Coat from curing due to contamination.

Allow 2-3 minutes of waiting time between Top Coat and Activator Coat.

Step 6: Top Coat

Apply a thin layer of Top Coat evenly with 2-3 quick strokes and allow it to dry for at least two minutes.

Step 7: Top Coat

Repeat step 6. Apply a second, thin coat of Top Coat to the nails. Then let this dry for 2-3 minutes.

---

And voila! With these simple steps, you will create beautiful, long-lasting nails with the 'Sapphire Black + Bright Gold + Reflective Diamond + Crystal Clear' dipping powder. Have fun with your beautiful nails!