Latte + Green Fields + Sacramento + Smooth Avocado + Blue-yond + Cryst

Products used:

Step-by-step instructions for applying "Latte + Green Fields + Sacramento + Smooth Avocado + Blue-yond + Crystal Clear" Dipping Powder

Materials:

Latte Dipping Powder
Green Fields Dipping Powder
Sacramento Dipping Powder
Smooth Avocado Dipping Powder
Blue-yond Dipping Powder
Crystal Clear Dipping Powder
Base coat
Activator
Top coat
Nail file and buffer
Dusting brush or soft brush

Preparation

File your nails into the desired shape and gently push back your cuticles.

For optimal adhesion, lightly roughen/match the natural nails with a buffer block or the fine side of a file before application.

Be sure to remove invisible cuticle and skin debris as well, to avoid lifting.

Do not apply oils or creams before use.

Step 1: Base coat

Apply a thin, even layer of Base Coat to the entire nail. The first coat should be quick and does not need to be too precise. Be careful not to touch the cuticles or surrounding skin, as this can cause lifting and affect adhesion.

Dip all nails fully into “Latte.” Tap off excess powder and gently brush away loose particles. Apply a second thin layer of base coat and repeat the dip into “Latte” to build a smooth, even base color. Brush clean and allow the layer to set before moving on to the design.

Once the Latte base is complete, apply base coat to the upper portion of the nail only, leaving the lower half exposed in a soft U-shape curve near the cuticle area. The curved opening should remain visible to create contrast in the design.

For the pointing (index) finger, thumb, and pinky, dip the coated upper section into “Green Fields.” Tap off excess and gently brush clean while keeping the curved U-shape defined.

For the middle finger, dip the coated upper section into “Sacramento.” Tap off excess and brush clean carefully.

For the ring finger, dip the coated upper section into “Smooth Avocado.” Tap off excess and brush away loose particles.

Next, apply a small dot of base coat in the center of the lower U-shaped area on each nail using a dotting tool or detail applicator.

For the middle finger (Sacramento nail), dip the dot into “Smooth Avocado.”

For the ring finger (Smooth Avocado nail), dip the dot into “Green Fields.”

For the thumb and pinky (Green Fields nails), dip the dot into “Sacramento.”

For the pointing (index) finger, dip the dot into “Blue-Yond.”

Tap off excess powder gently and brush clean carefully to maintain the shape and placement of the dots.

To finish, apply a thin, even layer of base coat over the entire nail and dip fully into “Crystal Clear.” This encapsulates the design, smooths the surface, and protects all color layers underneath for a glossy, long-lasting finish.

Be sure to cover the edges well on all nails, but avoid touching the surrounding skin to ensure proper adhesion and a clean, polished result.

Step 2: Base Coat & Color Powder

Repeat step 1 for optimal coverage, adhesion and beautiful and stunning color intensity.

Step 3: Activator Coat

Apply enough Activator Coat over the entire nail surface, edges and also at the tip. The Activator is the most important step in the application process because it seals and binds the layers to the nail, preventing air bubbles from forming and ensuring long-lasting adhesion. Allow the Activator Coat to dry for at least two minutes.

Step 4: Filing & Polishing

Now you can use the fine side of the file or a buffer to buff away all bumps and imperfections and bring the nails to the desired shape and thickness. It is important to file carefully so that you do not damage the surface and nails.

Step 5: Activator Coat

Repeat step 3. Again, apply enough Activator Coat to the entire nail and its perimeter to seal the layers optimally. Then allow the Activator Coat to dry for at least two minutes. To make sure the Activator Coat is dry, you can clean the surface of the nail with a paper towel after 2 minutes. This is to prevent the Top Coat from curing due to contamination.

Allow 2-3 minutes of waiting time between Top Coat and Activator Coat.

Step 6: Top Coat

Apply a thin layer of Top Coat evenly with 2-3 quick strokes and allow it to dry for at least two minutes.

Step 7: Top Coat

Repeat step 6. Apply a second, thin coat of Top Coat to the nails. Then let this dry for 2-3 minutes.

And voila! With these simple steps, you will create beautiful, long-lasting nails with the 'Latte + Green Fields + Sacramento + Smooth Avocado + Blue-yond + Crystal Clear' dipping powder. Have fun with your beautiful nails!