Old Pink + Olive Dusk + Smoke + Crystal Clear

 

Products used:

- Glowdip starter set

- Colour: Old Pink

- Colour: Olive Dusk

- Colour: Smoke

- Colour: Crystal Clear 

Step-by-step instructions for applying "Old Pink + Olive Dusk + Smoke + Crystal Clear" Dipping Powder

Materials:

• Old Pink Dipping Powder
• Olive Dusk Dipping Powder
  
• Smoke Dipping Powder
• Crystal Clear Dipping Powder
• Base coat
• Activator
• Top coat
• Nail file and buffer
• Dusting brush or soft brush

Preparation

File your nails into the desired shape and gently push back your cuticles.

For optimal adhesion, lightly roughen/match the natural nails with a buffer block or the fine side of a file before application.

Be sure to remove invisible cuticle and skin debris as well, to avoid lifting.

Do not apply oils or creams before use.

Step 1: Base coat

Apply a thin layer of Base Coat. The first coat should be quick and does not need to be too precise. Be careful not to paint the cuticles, as this can cause air bubbles under the nails and affect adhesion.

For the base color, apply base coat and dip each nail into either “Old Pink” or “Olive Dusk.” Submerge the nail at a slight angle to achieve smooth, even coverage. Tap off the excess powder and gently brush away any loose particles with a soft brush. Apply a second thin layer of base coat and repeat the dip into the same color to build opacity and ensure an even base.

For the pointing (index) finger, apply base coat only to the upper portion of the nail where the French tip will sit. Carefully dip that section into “Smoke” to create a soft French tip. Tap off excess powder and brush clean, making sure the smile line remains crisp.

For the pinky finger, repeat the same French tip process. Apply base coat only to the tip of the nail, then dip that area into “Olive Dusk.” Tap off excess and brush away loose powder, ensuring the tip remains clean and defined.

For the thumb design, apply a small amount of base coat to the upper left area of the nail. Using a fine tool or brush dipped in base coat, draw three short stroke lines that resemble small petals or leaf strokes. Immediately dip the nail into “Olive Dusk” so the powder adheres only to those strokes. Tap off excess and brush clean.

Next, repeat the same petal-stroke process on the lower left side of the thumb. Apply base coat in three short strokes again, then dip the nail into “Smoke.” This step should be done separately so the two colors remain distinct and clean. Tap off excess powder and gently brush away loose particles.

Once all designs are complete, apply a thin, even layer of base coat over the entire nail surface and dip each nail fully into “Crystal Clear.” This step encapsulates the design, smooths the surface, and protects the artwork underneath. Tap off excess and brush clean, ensuring the edges are well covered while avoiding contact with the surrounding skin for the best adhesion and durability.

Be sure to cover the edges well, but do not touch the skin around the nail.

Step 2: Base Coat & Color Powder

Repeat step 1 for optimal coverage, adhesion and beautiful and stunning color intensity.

Step 3: Activator Coat

Apply enough Activator Coat over the entire nail surface, edges and also at the tip. The Activator is the most important step in the application process because it seals and binds the layers to the nail, preventing air bubbles from forming and ensuring long-lasting adhesion. Allow the Activator Coat to dry for at least two minutes.

Step 4: Filing & Polishing

Now you can use the fine side of the file or a buffer to buff away all bumps and imperfections and bring the nails to the desired shape and thickness. It is important to file carefully so that you do not damage the surface and nails.

Step 5: Activator Coat

Repeat step 3. Again, apply enough Activator Coat to the entire nail and its perimeter to seal the layers optimally. Then allow the Activator Coat to dry for at least two minutes. To make sure the Activator Coat is dry, you can clean the surface of the nail with a paper towel after 2 minutes. This is to prevent the Top Coat from curing due to contamination.

Allow 2-3 minutes of waiting time between Top Coat and Activator Coat.

Step 6: Top Coat

Apply a thin layer of Top Coat evenly with 2-3 quick strokes and allow it to dry for at least two minutes.

Step 7: Top Coat

Repeat step 6. Apply a second, thin coat of Top Coat to the nails. Then let this dry for 2-3 minutes.

---

And voila! With these simple steps, you will create beautiful, long-lasting nails with the 'Old Pink + Olive Dusk + Smoke + Crystal Clear' dipping powder. Have fun with your beautiful nails!